Water tank leakage and solution

Water tank leak, maintenance personnel can not arrive in time to repair the location, the user should do, do not worry there are three emergency solutions provided by Hebei LongTime Water Tank Company.
1, with adhesive repair tank
(1) with a metal cleaning agent cleaning crack, with a scraper scraping the paint here, dirt and rust, etc., and along the crack shovel out the trench, and then repeatedly cleaned with gasoline. The same time as
(2) the xh-ii type adhesive a, b components of the same amount of extrusion, and agricultural machinery No. 1 adhesive (the amount of the adhesive is about i / 3) repeatedly withered. The same time as
(3) cut two pieces of oil-free, slightly larger than the groove surface of broken glass fiber cloth, coated with a layer of adhesive.
(4) will be coated with adhesive fiber cloth posts on both sides of the crack, over io minutes - 15 minutes, then wiping a layer of adhesive, curing at room temperature for 25 hours after use.
2, with adhesive penetration method repair tank crack
(1) to dry the tank, drilling at both ends of the hole 3 mm hole, such as the crack is longer or curved, can be in the middle or corner and then drill a hole, with the scraping scraping crack, revealing metallic luster. The same time as
(2) with 5o2 adhesive drops in two holes, with 3 mm aluminum rivet riveting, closed crack. The same time as
(3) the adhesive drops in the crack, and then use the hammer in the cracks in the two measured percussion, the adhesive into the cracks, every 3o minutes and then add the adhesive and knock, repeat 2 times -4 times, until the glue can not penetrate, 3 hours -5 hours to use.
3, with tin zinc aluminum alloy welding aluminum tank
Will be 6o% of tin, 35% of the zinc and 5% of the aluminum iron spoon and other items in the heating and melting, cast into a thin electrode.
Cleaning the crack at the oil, with an abrasive cloth polished oxide film, and then a screwdriver or broken blade scraping clean, with a torch to aluminum heating to 300 ℃ -40o ℃ (note the temperature can not be too high), the electrode rubbed in the crack When the electrode melts, use a screwdriver to rub the molten alloy alloy at the crack, so that the alloy flows into the crack, and then gradually thicker the solder layer
Stainless steel water tank leakage is the result of household water waste a large "cancer", saving water to eradicate this big "cancer"

1. Check that the stainless steel tank cover is fastened.
2. Try to enter the stainless steel tank, see the water tank when the water pressure from which the location of seepage, and then decided to repair the program.
3. Unscrew the engine with oil cover to see if there is any oil in the oil, if any, open the engine to replace the cylinder pad.
  If the car is running in the process, due to vehicle vibration or vehicle accidents, so that the water tank rupture leakage, according to the specific circumstances to take measures:
Leakage of not more than 1mm cracks or 2mm hole, the stainless steel tank to add a bottle of water tank strong plugging agent, start the car running.
Open the cooling water began a large cycle after 5 to 10 minutes, the cooling system, whether it is water tank or rubber tube and the pad everywhere, there will be leakage of water leakage, leakage does not need to release, will not affect the heat and clogging.
If there is no leakage agent to carry, the individual heat pipe slightly leaking, can be temporarily with a separate cigarette into the water tank, the use of water circulation pressure, so that the smoke plug in the heat pipe leak, temporarily not used.
Combination of stainless steel water tank, completely solve the traditional water tank production of rough, difficult to install, poor anti-corrosion effect, short life and other defects.
Water tank leakage to solve the two major programs; we in front of the water tank market up to two categories of stainless steel water tanks and glass steel tank, the water tank leakage problems; general glass steel tank water leakage areas are mainly concentrated in: sheet, sheet and sheet joints, four Angle and plugging. If it is a sheet of cracks leaking, the seam is very small, you can use sealant or water does not leak in the tank internal repair, the method is; to put the water finished, dried, sealant or water leaked to the leaky parts can be; If the four corners and plugging at the water, that the tape is not put away or plugging the direction of dislocation, repair method is to plug out, and then put some strips, re-installed on it.

      Stainless steel water tank where the water is generally the flange or four corners, because the other places have been tried in the welding finished, there will be no water leakage. Stainless steel tanks are generally welded, you can wipe the place to wipe clean, from the new welding or change the flange. If it is a combination of stainless steel water tank, there may be the reason for the sealing pad, so you can tighten the flange screw, or directly change the seal pad.
Water tank leakage is a result of household water waste a large "cancer", found that the problem should be resolved in time to prevent the water tank leakage!
     Stainless steel water tank is made by welding method, that is, there are leakage welding or slag eyes. In the water tank parts to do the mark, re-welding. If it is not easy to repair welding, glass glue can be used to close the leaky parts. But pay attention to the closure before the leaky parts to be clean, dry, sealed and then wait for the plastic and then dry. Stainless steel is an anti-corrosion material, no special treatment. If necessary, you can choose 304,308,316 and other models of stainless steel materials, welding to use the same type of electrode.
Stainless steel tank leakage and rust causes; generally contact with the water must be made of stainless steel. When using stainless steel water tank, do not apply excessive load to piping inlet and outlet. Do not apply the weight of the valve and the large diameter pipe directly to the tank outlet, if necessary, set the pipe support: the expansion of the pipe, shrinkage, vibration must be fitted flexible flexible joints.
All above are the solutions for the leakage of water tank. i hope that it can help you. if you want to know more about our company or our products, please contact us on E-mail: rask@coolingtowerfiller.com, you can also chat us straightly on whatsapp: 008618330029204.